Lowbrow Customs Original P-Nut Gas Tank peanut wassell Triumph bobber chopper

Description

Lowbrow Customs Original P-Nut Gas Tank peanut wassell Triumph bobber chopper
The Original P-Nut Tank, from Lowbrow since 2010! Nothing changes the look of your hand-built custom motorcycle like a new bobber gas tank. The Lowbrow P-Nut Gas Tank is a tidy, 1.8-gallon chopper gas tank based on the old Wassell peanut gas tanks available for custom bikes in the 1950's - 70's. They hadn't existed except as relics found on eBay or swap meets, overpriced for an old tank that is rusty, crusty, and likely needs work to repair leaky seams. In addition, the heavy gauge (1mm, approximately 19 gauge) steel used on the P-Nut Tank is much thicker, and the fabrication much higher quality, than the originals. The Original P-Nut Tank has a deep tunnel, it sits low down on the backbone of your frame. - Deep tunnel, sits low down on the backbone of your frame- Two 1/4 inch NPT petcock bungs for delivering fuel to your carburetors- Filler accepts a Triumph-style gas cap (not included), which we have available in a high-quality imported version as well as a UK-made version. The P-Nut Tank is intended for use on custom motorcycles, be it a bobber, chopper, cafe racer, vintage motorcycle or fresh off the showroom floor. This gas tank features two 1/4" NPT petcock bungs and undrilled mounting tabs for custom installation, and will accept a Triumph or British-style gas cap (not included). Most people drill holes in the backbone of their frame, weld some blind threaded tophat bungs in place, and bolt the tank down using some leather washers to cushion between the gas tank tabs and the frame. Note: It is highly recommended to fit your gas tank to your bike before painting. Check for clearance or mounting issues as different combinations of triple trees, risers, and handlebars may cause clearance issues when turning. Tanks are pressure tested but it is highly recommended that you or your painter pressure test it again before painting; it's cheap insurance!
Lowbrow Customs Original P-Nut Gas Tank peanut wassell Triumph bobber chopper
The Original P-Nut Tank, from Lowbrow since 2010! Nothing changes the look of your hand-built custom motorcycle like a new bobber gas tank. The Lowbrow P-Nut Gas Tank is a tidy, 1.8-gallon chopper gas tank based on the old Wassell peanut gas tanks available for custom bikes in the 1950's - 70's. They hadn't existed except as relics found on eBay or swap meets, overpriced for an old tank that is rusty, crusty, and likely needs work to repair leaky seams. In addition, the heavy gauge (1mm, approximately 19 gauge) steel uséd on the P-Nut Tank is much thicker, and the fabrication much higher quality, than the originals. The Original P-Nut Tank has a deep tunnel, it sits low down on the backbone of your frame. - Deep tunnel, sits low down on the backbone of your frame
- Two 1/4 inch NPT petcock bungs for delivering fuel to your carburetors
- Filler accepts a Triumph-style gas cap (not included), which we have available in a high-quality imported version as well as a UK-made version. The P-Nut Tank is intended for use on custom motorcycles, be it a bobber, chopper, cafe racer, vintage motorcycle or fresh off the showroom floor. This gas tank features two 1/4" NPT petcock bungs and undrilled mounting tabs for custom installation, and will accept a Triumph or British-style gas cap (not included). Most people drill holes in the backbone of their frame, weld some blind threaded tophat bungs in place, and bolt the tank down using some leather washers to cushion between the gas tank tabs and the frame. Note: It is highly recommended to fit your gas tank to your bike before painting. Check for clearance or mounting issues as different combinations of triple trees, risers, and handlebars may cause clearance issues when turning. Tanks are pressure tested but it is highly recommended that you or your painter pressure test it again before painting; it's cheap insurance!
×
×
×
×
×
×
×
×
×
×
×
×
×
Lowbrow was started in 2004, a physical manifestation of chopper fever and passion for all things motorcycle. We are the premier source for custom and chopper parts for your moto, backed by a tight-knit crew here in northeast Ohio who strive to make your experience with us the best possible. We not only work hard to supply motorcycle enthusiasts with cool parts from small shops all around the world, but to also keep innovating and building, creating brand new parts and accessories, getting them out onto the road.
eBay integration
by